How does the Two-Step Media Recovery look like

From Wiki-UX.info
Jump to: navigation, search

1. Load Kernel from DVD

Starting: Internal Bootable DVD

(C) Copyright 1999-2008 Hewlett-Packard Development Company, L.P.
All rights reserved

HP-UX Boot Loader for IPF  --  Revision 2.037

Press Any Key to interrupt Autoboot
\EFI\BOOT\AUTO ==> boot :IINSTALL

2. Finished Kernel load

Seconds left till autoboot -   0
AUTOBOOTING...> System Memory = 4064 MB
loading section 0
...................................................................................................... (complete)
loading section 1
.................... (complete)
loading symbol table
loading ram disk file (:IINSTALLFS).
.....................................................................................................................
 (complete)
Launching :IINSTALL
SIZE: Text:51786K + Data:10060K + BSS:25412K = Total:87259K
Console is on Serial Device - via PCDP
Booting kernel...


3. - Ignite Welcome Screeen

.
                         Welcome to Ignite-UX!

  Use the <tab> key to navigate between fields, and the arrow keys
  within fields.  Use the <return/enter> key to select an item.
  Use the <return/enter> or <space-bar> to pop-up a choices list.  If the
  menus are not clear, select the "Help" item for more information.

  Hardware Summary:         System Model: ia64 hp server rx6600
  +----------------------+---------------+--------------------+[ Scan Again  ]
  | Disks: 2  (  273.5GB)| Floppies: 0   | LAN cards:   6     |
  | CD/DVDs:        1    | Tapes:    1   | Memory:     4064Mb |
  | Graphics Ports: 0    | IO Buses: 11  | CPUs:        4     |[ H/W Details ]
  +----------------------+---------------+--------------------+

                       [      Install HP-UX       ]

                   [   Run an Expert Recovery Shell   ]

                       [    Advanced Options      ]


          [  Reboot  ]                              [  Help  ]


4. Ignite-UX "Install HP-UX"


.
                        User Interface and Media Options

   This screen lets you pick from options that will determine if an
   Ignite-UX server is used, and your user interface preference.

 Source Location Options:
   [ * ]  Media only installation
   [   ]  Media with Network enabled (allows use of SD depots)
   [   ]  Ignite-UX server based installation

User Interface Options:
   [ * ]  Advanced Installation (recommended for disk and filesystem management)
   [   ]  No user interface - use all the defaults and go


   Hint: If you need to make LVM size changes, or want to set the
         final networking parameters during the install, you will
         need to use the Advanced mode (or remote graphical interface).




   [   OK   ]                  [ Cancel ]                         [  Help  ]


5. Media Installation Selection

.
                          Media Installation Selection

   This screen provides an option to switch the install source
   from the default CD/DVD to a recovery tape.  This is helpful
   for those systems and for tape devices which do not support
   booting from a tape.


   [ * ]  CD/DVD Installation
   [   ]  Boot from CD/DVD, Recover from Tape












   [   OK   ]                  [ Cancel ]                         [  Help  ]


6. Tape Drive Selection

.
                              Tape Drive Selection

    There are one or more tape drives detected on the system.  Insert
    your recovery tape into one of the drives and then select that drive
    from the list below.

    Use the <tab> and/or arrow keys to move to the desired TAPE device,
    then press <Return/Enter> to select.

       HW Path           Device File            Description
       ----------------------------------------------------------


     [ 0/1/2/0.0x0.0x0 /dev/rmt/c0t0d0BEST       HP_Ultrium_1-SCSI         ]


7. Checking Ignite-UX version in the tape

Mon Jan 25 13:01:02 CST 2010